Apply Bedliner Height and Surface Whether a surface to be sprayed is the bed of a truck or any other substrate 2 dimensions must be considered: total area & height. Where area is mentioned mostly, that 2nd dimension, in the world spray on bedliner of sprayed truck bed liners cannot be overlooked. The height dimension is its thickness which is much more important than area in determining the apply lining job’s quality. Actual product qualities must also matter & is discussed later.
Apply Bedliner Professional versus DIY Kits Professional Apply Lining Higher grade apply on lining jobs applied by professionals contain enough hazardous ingredients to limit or prevent their use outside of a paint presentation area to contain these toxins with protective taking in oxygen gear for the applicator. They are at least 2 parts, require correct preparation & many require highly specialized equipment to apply. These formulations usually provide very high specifications strength characteristics which might rationalize their higher cost than DIY. Cost range is just $300. 00 & can exceed $600. 00 depending on the size part of the box to be covered. Thickness must play a role in cost since it’s the only direct correlation to the number of gallons of costly product being applied & sold retail.
DIY Kit Apply Bed Lining DIY bed ship formulations are risk less for use by the consumer. These are usually 1 part, applied with a simple apply rifle or basic roller & simple directions. Although surface preparation is important most DIY bed liners don’t mention this as a necessity. Most of these are urethanes sold as 1 gallon to cover a full size truck bed available through stores. Average retail price is $100. 00 plus tax with a little roller, exceeding beyond $130. 00 with a basic apply rifle included.
Apply Bedliner Coverage Formula This Coverage Formula garden sheds light on dull areas or mysteries with lining a truck bed (or any surface requiring superior protection): 1 gallon of any liquid means 1, 604 sq feet at the height of 1/1, 000 of an inch (1 mil). This considers no loss to overspray or evaporation.
Although some spray-on bed ship companies state, “1/4 inch thick” (250 mils), this height is rarely when needed or true. In fact with any high specifications professional application 1/8 inch (125 mils) usually provides many years of protection on a truck bed. For purposes of average calculations if we think about a full size bed to be 8 feet long, 6. 5 feet wide & 2 feet high, then outside dimensions equal 110 sq legs. It’s commonly known inside dimensions of a full size truck box is about eighty-five sq legs with bed rails covered. An economy bed is about 50 sq legs which leaves an average of 62. 5 sq legs. We’ll use 62. 5 for purposes of simplicity.
Before applying our coverage formula it ought to be understood that because of apply on product’s high expense maximum thickness really should not be necessary over all parts of a truck bed. Main areas of highest stress on a truck bed are the tailgate, backside half end of the bed, lower sidewalls & back of fender water wells. This leaves the top of walls, inner box & cab’s wall to be much less thick with full protection; this is about. 5 of the area. We’ll use an average height of 67. 5 mils… (125 mils = maximum with a thinner coat on less stressed parts & 10 mils for close to no stress specific zones like under the bed rails = 135/2)= 67. 5 mils average thickness required for long term protection.
Using 62. 5 sq legs average area & 67. 5 mils average height we can now apply the formula for accurate computations: 1 gallon = 1, 604 sq legs at 1 mil means 12. 8 sq legs at 67. 5 mils thick. Now if the average bed is 62. 5 sq legs, just partition by 12. 8 = 2. 6 gallons. Because of this apply lining an average truck bed at fair height for long term protection requires a minimum of 2. 6 gallons of product.
As of this rate DIY apply on bed ship kits consisting of 1 gallon are insufficient for real protection over the long corridor. At a cost of $100. 00 per gallon this means $260. 00 (2. 6 X $100. 00) or $290. 00 with a basic apply rifle plus tax for a fair thickness. This price doesn’t take into account incidental supplies & the value of your energy to line your bed. This also considers you’d have some skill to apply it thicker where needed with a consistent or neat appearance. As for getting it sprayed by a professional, OEM pricing of higher a grade apply lining product range from about $20 to $60 per gallon; the average being $40/gallon.
You may now understand with an average cost of goods at $104. 00 (2. 6 X $40) plus labor & business costs, why the product range of $300. 00 to $600. 00 can be a fair price to have an experienced or specially trained professional line your truck bed with the correct amount of high grade product generally inaccessible in DIY bed ship kits.
Factors of Apply Bedliner Quality
THINK ABOUT QUALITY? It stands to reason that all bed lining essential fluids are not the same formula. And we already know that quality must also depend of thickness which is the amount of product. The reason why professionally applied apply lining products require specialized protection is due to 2 ingredients: VOC (Volatile Organic Compounds) & isocyanates. In general these substances create rapid drying out, better adhesion and higher strength (specialized characteristics are known as tensile or grab psi, data compresion strength, elongation, elasticity & shore hardness). Unfortunately these being toxic & carcinogenic they’re not safe & usually not legal to use in a non-professional, protected area inside a building. Because of this DIY cannot match the standard of professionally applied bed liners. As for qualities due to specifications between brands or different products employed by professional bed ship shops, the golf pros should have these specs documented & available for comparison where DIY kits rarely or never mention or document any quality specs.